priorto having this issue (oil pressure gauge dropping to zero at idle because the sensor was soaked in pwr steering fluid) the oil pressure gauge (real gauge - 2001 WJ v8) always stayed around 45-50 psi . but now after putting in the new sensor it seems to stay around 55-60 psi. The FSM isn't much help, all I can find in there for the v8
TheCheck Engine Light comes on whenever the systems send out an abnormal reading. For that reason, many issues cause the warning. However, the most common causes are a loose gas cap, a bad EGR valve, a bad MAF sensor, a bad oxygen sensor, a worn-out catalytic converter or a bad ignition coil. 1. Loose Gas Cap.
Thisis a video showing you how to do an oil change on a 2017 Jeep Grand Cherokee V6. I hope you find this video helpful. Like and Subscribe!
\n\n\n\n\n \n2010 jeep grand cherokee oil change reset
Leiffrom 824 Workshop takes you step-by-step through the process of changing the oil pressure sensor in a 2015 Jeep Cherokee.Stay connected at:Email: 824Wor
Pressdown the gas pedal 3x within ten seconds. Turn the ignition off. After these steps have been performed, you have successfully reset the oil life on the Jeep Cherokee. Repeat the steps if you cannot reset the “Oil Change Required” light utilizing one of these methods. If you are still unsuccessful, contact the dealership for assistance STEP1 Close all doors. STEP 2 Set the gear to the PARK position. STEP 3 Turn ignition to RUN position, don’t start the engine. STEP 4 fully depress the accelerator pedal slowly three times within 5 seconds 3 Wait two minutes. (do not skip this step!) 4. Reconnect battery. 5. Start car, look at light, drive around block a few times and stop at corner store and buy some smokes and a JP magazine. 6. Drive home. 7. look at light.

fireron My guess is you did not reset the oil change indicator, therefore the computer just went by your driving habits and mileage combo. Just a thought. But the manual does state 8,000 miles or 6 months for an oil change, whichever comes first, to keep your warranty valid. Many folks on here seem to miss that point.

Theoil change indicator can be reset using the following steps: 1. Turn the ignition key to ON but do not start the engine. 2. Slowly depress the accelerator to the floor and release it three times within 10 seconds. 3. Turn the ignition key to the OFF position. Repeat the process if the indicator does not reset. Hereare the most common symptoms of burning oil: 1. Blue Smoke. The most obvious and a telltale sign that your Grand Cherokee is burning oil is blue smoke. Blue smoke indicates that oil has made its way to the combustion chamber. It is then burned with the gasoline and tints the exhaust blue. Your exhaust will look more like a two stroke Thedealer can set the max oil change interval to 3000 or 6000 (not sure about intervals in between). The change oil light will illuminate 500 miles before you need to act on it. The interval that you will actually get depends on how you drive according to an algorithm set up in the computer. So far, in 42,000 miles of driving mine has
Todeactivate the TPMS, first, replace all four wheel and tire assemblies (road tires) with tires not equipped with Tire Pressure Monitoring System sensors. Then, drive the vehicle for 20 minutes above 15 mph (24 km/h). The TPMS will chime, the TPMS Warning Light will flash on and off for 75 seconds and then remain on.
2 Fully depress the accelerator pedal and keep it fully depressed for at least 30 seconds. 3. Press and release the brake pedal six times while holding the accelerator pedal pressed. 4. Perform one ignition OFF-ON cycle, start the engine and verify that the reminder has been reset. Toreset your Jeep Grand Cherokee’s climate control system, you’ll need to turn the entire system off and back on. We’ll walk you through it step by step. You can easily replace the power steering fluid in your 2011 Honda Accord by following the steps in this customized how-to guide. Kathryn Mae Kurlychek. Jan 5, 2024.
HowTo Fix Check Engine Light Jeep Grand CherokeeBuy the Scanner here at Amazon - just replace a battery on my 2016 Jeep Cherokee, a
Heres a how to to reset your oil life setting in your car. I've had oil changing services done and they don't see the warning so they don't reset it. So her
Inthis video I show you how to reset the oil change required message on your 2010 Jeep Cherokee after you have had an oil change and the mechanic forgot to do it because he was
2020Jeep Cherokee features an automatic oil change message to let you know when an oil change is required. This feature will help you know how often to chan
Toreset the 2017 Jeep Cherokee engine oil life after an oil change service, please follow these instructions: 1. Turn the ignition to run (one position before starting engine). 2. Fully depress the accelerator pedal slowly three times within 10 seconds. 3. Turn the ignition off and then start the engine to verify the indicator has been reset
.